文章摘要
董延娟,郝建华,郑鸿飞,孙 谧.产木聚糖酶菌株YS1069的产酶条件优化.渔业科学进展,2016,37(3):154-159
产木聚糖酶菌株YS1069的产酶条件优化
Optimization of the Fermentation Conditions for Xylanase-Producing Strain YS1069
投稿时间:2015-04-30  修订日期:2015-06-07
DOI:10.11758/yykxjz.20150430003
中文关键词: 芽孢杆菌  木聚糖酶  响应面  发酵条件  优化
英文关键词: Bacillus  Xylanase  Response surface methodology  Fermentation conditions  Optimization
基金项目:国家自然科学基金-联合基金(U1406402-5)和国际科技合作与交流专项(2014DFG30890)共同资助
作者单位
董延娟 农业部海洋渔业可持续发展重点实验室 青岛市海洋酶工程重点实验室 中国水产科学研究院黄海水产研究所 青岛 266071上海海洋大学食品学院 上海 201306 
郝建华 农业部海洋渔业可持续发展重点实验室 青岛市海洋酶工程重点实验室 中国水产科学研究院黄海水产研究所 青岛 266071 
郑鸿飞 农业部海洋渔业可持续发展重点实验室 青岛市海洋酶工程重点实验室 中国水产科学研究院黄海水产研究所 青岛 266071 
孙 谧 农业部海洋渔业可持续发展重点实验室 青岛市海洋酶工程重点实验室 中国水产科学研究院黄海水产研究所 青岛 266071 
摘要点击次数: 2871
全文下载次数: 3049
中文摘要:
      为获得较高的木聚糖酶产量,采用单因素实验和响应面实验方法,筛选氮源、碳源、无机盐、接种量、装液量、Na2CO3、发酵温度、发酵时间多个单因素,对产木聚糖酶的芽孢杆菌YS1069的发酵培养基和发酵条件进行了优化。结果显示,豆饼粉25 g/L、麸皮40 g/L、NaNO3 0.9 g/L、K2HPO4 3 g/L、MgSO4·7H2O 0.6 g/L、接种量4%、装液量30 ml/250 ml(v/v)、Na2CO3添加量18 g/L、培养温度30℃、培养时间96 h时,酶活性达到最高。再通过Plackett-Burman设计对影响木聚糖酶产量的8个主要因素进行评价,确定Na2CO3浓度、麸皮浓度和MgSO4·7H2O浓度是影响产酶量的3个主要因素。利用中心组合设计及Design-Expert 8.05软件分析,获得了主要因素的最优条件,即Na2CO3浓度21.86 g/L、麸皮浓度51.41 g/L、MgSO4·7H2O浓度0.59 g/L,实验最终酶活性比发酵优化前提高了5倍。
英文摘要:
      In this study we applied one-single factor and response surface method to optimize the culture medium and other conditions for strain YS1069, which would improve the yield of xylanase. First, the single factor method was used to screen eight factors including the nitrogen source, the carbon source, the inorganic salts, the inoculation volume, the liquid volume, Na2CO3, fermentation temperature and fermentation time. The optimal results corresponding to each single factor was as follows: bean cake powder 25 g/L, wheat bran 40 g/L, NaNO3 0.9 g/L, K2HPO4 3 g/L, MgSO4·7H2O 0.6 g/L, inoculums at 4%, 30 ml/250 ml (v/v) liquid volume, Na2CO3 18 g/L, cultured at 30℃ for 96 h. Secondly, these main variables were evaluated with the Plackett-Burman test. The results suggested that Na2CO3, wheat bran and MgSO4·7H2O were the most impactful factors. Finally, the optimal levels of the three factors were determined with central composite design and Design-Expert 8.05 software. The results were shown as follows: Na2CO3 21.86 g/L, wheat bran 51.41 g/L, and MgSO4·7H2O 0.59 g/L. Under the optimized conditions, the production of xylanase was increased by 5 folds.
附件
查看全文   查看/发表评论  下载PDF阅读器
关闭